Cable Trays for United States projects, made in India
What it takes to land cable trays on a United States site: the port they clear through, the standards a consultant will hold them to, and the paperwork that has to travel with them.
Getting cable trays into United States
American buyers rarely doubt Indian capacity. They doubt whether the paperwork survives an ASTM review, which is a fair doubt, because plenty of it does not. We galvanize to ASTM A123 and ship the mill test certificates with the container, so the check happens on your desk instead of on trust.
Port of entry
Port of Houston, TX
Also cleared through Port of Los Angeles / Long Beach, CA, Port of Newark, NJ.
Shipped FOB, CIF, CFR.
Standards that apply here
- ASTM A123
- ASTM A36
- NEMA VE-1
- UL Listed
- ISO 9001:2015
- IEC 61537
- IS 12352
- NEMA VE 1
Every shipment travels with mill test certificates against the grade specified on your order.
Who buys this in United States
Oil & Gas · Solar & Renewable Energy · Data Centres · Automotive & CNC · Construction · Utilities & Power
Trade picture
USA is the #1 importer of steel structures from India. 54% share, 434 shipments under HSN 7308. #1 for solar module mounting structures. CNC cables grew at 44% CAGR FY17–FY24.
Cable Trays
Vajra International is an ISO 9001:2015-certified cable tray manufacturer and exporter in Kolkata, India, producing ladder, perforated and raceway cable trays to IEC 61537 and IS 12352. Trays are roll-formed in-house in MS, GI, stainless steel and aluminium: pre-galvanized for indoor and dry duty, hot-dip galvanized to a minimum average 85 µm per ASTM A123 for outdoor and coastal exposure, or powder coated where colour-coding is specified. Shipped direct on FOB/CIF terms with the matched accessory and support range, mill test certificates and full export documentation.
Before you write the enquiry
The technical detail behind the decisions on this page.
- Technical Guide
Cable Tray Specification Guide: Ladder vs Perforated vs Trunking
Most cable tray failures start at the bolt hole, tray type, gauge and the fabrication detail that separates 5-year trays from 25-year ones.
- Materials
Hot-Dip vs Pre-Galvanized Steel: Lifecycle Cost & Coating Guide
Pre-galvanized saves 15% on day one and costs 300% more by year five outdoors. The actual zinc numbers and lifecycle calculation that settles the choice.
- Export
Indian Metal Export Documents: MTC, COO & HS Codes Explained
Getting the HS code wrong holds containers at port. Every document needed for an Indian metal export, and the specific errors that cause delays.
- Buyer's Guide
Cable Tray Manufacturers India: Specification & Qualification
Buyers qualifying Indian cable tray manufacturers ask the same eight questions. The complete specification and qualification guide, with the answers.
Other lines going into United States
Cable Trays into United States — the questions that come up
Answered by the people who make the product, not a sales desk.
Common gauges are 1.2, 1.6, 2.0 and 2.5 mm. 1.2 mm suits light control cabling on short spans, 1.6 mm is the general-purpose default, and 2.0 to 2.5 mm is for heavy power runs, wide trays or long support spans. Rather than order by gauge alone, give the cable load per metre and support spacing, and let the manufacturer confirm the thickness.
Add the cross-sectional area of all cables, then keep the fill ratio below about 40% of the tray's internal area so heat can dissipate, per IEC 61537 practice. Don't stack a single layer of power cable; for control cable, 40% fill is acceptable. Share the cable schedule and we can confirm tray width, depth and load class before fabrication.
A credible Indian manufacturer ships a commercial invoice, packing list, Mill Test Certificate (MTC) tracing the steel to its heat, a galvanizing certificate stating zinc thickness, and a Certificate of Origin (COO) for duty relief. Third-party inspection reports from SGS, TÜV or Bureau Veritas are added where the buyer or the standard requires them.
There is no fixed minimum for international supply. Partial containers get consolidated with accessories and documentation into one shipment routinely. Most first-time orders are sized to fill a 20 ft or 40 ft container simply because that's the efficient freight unit. Tell us the destination port and Incoterm and we'll confirm what order size makes sense.
Only with internal dividers (or compartmented trunking). IEC 60364 requires separation between low-voltage power and ELV signal/data cabling. We supply dividers in matched finish, height-stepped to suit the largest cable, so the installation passes audit cleanly.
Send us the cable trays spec for your United States job.
Drawings, a BOQ line, or the standard you have been given. You will get back specification, finish, lead time and a landed price to Port of Houston.
- MTC · COO · inspection reports
- ±0.01 mm precision · in-house QA
- FOB · CIF · CFR to all major ports